Hiseeu 5MP PTZ gk7605v100 sc223a - Revision history

Damme: /* uart */

2023-08-09T14:05:20Z

uart

← Older revision		Revision as of 14:05, 9 August 2023
Line 103:		Line 103:
	ipctool reginfo \| grep UART		ipctool reginfo \| grep UART

	devmem ~~0x100c000c~~ 32 ~~0x02~~		devmem 0x112c0078 32 0x01
	devmem ~~0x100c0010~~ 32 ~~0x02~~		devmem 0x112c007c 32 0x01

	</syntaxhighlight>		</syntaxhighlight>

Damme: /* reflash kernel via uboot */

2023-08-09T13:24:48Z

reflash kernel via uboot

← Older revision		Revision as of 13:24, 9 August 2023
Line 109:		Line 109:
	== reflash kernel via uboot ==		== reflash kernel via uboot ==
	<syntaxhighlight lang="bash" line="1">		<syntaxhighlight lang="bash" line="1">
			## does not work?
	setenv ipaddr 192.168.1.10; setenv serverip 192.168.1.11		setenv ipaddr 192.168.1.10; setenv serverip 192.168.1.11
	setenv flash_addr 0x50000		setenv flash_addr 0x50000
			setenv uimage_size 0x300000

	mw.b ${baseaddr} 0xff 0x1000000		mw.b ${baseaddr} 0xff 0x1000000
Line 116:		Line 118:
	sf probe 0; sf lock 0;		sf probe 0; sf lock 0;

	sf erase ${flash_addr} ${~~filesize~~}		sf erase ${flash_addr} ${uimage_size}
	sf write ${loadaddr} ${flash_addr} ${filesize}		sf write ${loadaddr} ${flash_addr} ${filesize}
			original:

			uknor16m=mw.b ${baseaddr} ff 1000000; tftpboot ${baseaddr} uImage.${soc} && sf probe 0; sf erase 0x50000 0x300000; sf write ${baseaddr} 0x50000 ${filesize}
			urnor16m=mw.b ${baseaddr} ff 1000000; tftpboot ${baseaddr} rootfs.squashfs.${soc} && sf probe 0; sf erase 0x350000 0xa00000; sf write ${baseaddr} 0x350000 ${filesize}

	</syntaxhighlight>		</syntaxhighlight>

Damme at 12:06, 9 August 2023

2023-08-09T12:06:52Z

@@ Line 105: / Line 105: @@
 devmem 0x100c000c 32 0x02
 devmem 0x100c0010 32 0x02
 </syntaxhighlight>

Damme: /* uart */

2023-08-09T11:59:46Z

uart

← Older revision		Revision as of 11:59, 9 August 2023
Line 85:		Line 85:

	== uart ==		== uart ==
	* ./general/package/all-patches/linux/9000-enable-~~uart2~~.patch		* ./general/package/all-patches/linux/9000-enable-uart1.patch
	<syntaxhighlight lang="bash" line="1">		<syntaxhighlight lang="bash" line="1">
	--- a/arch/arm/boot/dts/gk7605v100-demb.dts 2023-08-09 13:43:00.715983714 +0200		--- a/arch/arm/boot/dts/gk7605v100-demb.dts 2023-08-09 13:43:00.715983714 +0200

Damme: /* uart */

2023-08-09T11:59:15Z

uart

← Older revision		Revision as of 11:59, 9 August 2023
Line 86:		Line 86:
	== uart ==		== uart ==
	* ./general/package/all-patches/linux/9000-enable-uart2.patch		* ./general/package/all-patches/linux/9000-enable-uart2.patch
	<syntaxhighlight lang="~~patch~~" line="1">		<syntaxhighlight lang="bash" line="1">
	--- a/arch/arm/boot/dts/gk7605v100-demb.dts 2023-08-09 13:43:00.715983714 +0200		--- a/arch/arm/boot/dts/gk7605v100-demb.dts 2023-08-09 13:43:00.715983714 +0200
	+++ b/arch/arm/boot/dts/gk7605v100-demb.dts 2023-08-09 13:42:25.609040743 +0200		+++ b/arch/arm/boot/dts/gk7605v100-demb.dts 2023-08-09 13:42:25.609040743 +0200

Damme at 11:58, 9 August 2023

2023-08-09T11:58:52Z

@@ Line 82: / Line 82: @@
 DevRect_w=1920
 DevRect_h=1080
 </syntaxhighlight>

Damme: Created page with "== Sensor == Camera needs _4l driver, got it from telegram channel. Source? config as follows: * /etc/sensors/sc223a_4l_i2c_1080p.ini [sensor] Sensor_type=stSnsSc223aObj Mode=WDR_MODE_NONE DllFile=libsns_sc223a_4l.so [mode] input_mode=INPUT_MODE_MIPI raw_bitness=10 [mipi] lane_id = 0|1|-1|-1|-1|-1|-1|-1| ;lane_id: -1 - disable [isp_image] Isp_FrameRate=30 Isp_Bayer=BAYER_BGGR [vi_dev] Input_mod=VI_MODE_MIPI Work_mod =0..."

2023-08-09T11:55:38Z

Created page with "== Sensor == Camera needs _4l driver, got it from telegram channel. Source? config as follows: * /etc/sensors/sc223a_4l_i2c_1080p.ini <syntaxhighlight lang="bash" line="1"> [sensor] Sensor_type=stSnsSc223aObj Mode=WDR_MODE_NONE DllFile=libsns_sc223a_4l.so [mode] input_mode=INPUT_MODE_MIPI raw_bitness=10 [mipi] lane_id = 0|1|-1|-1|-1|-1|-1|-1| ;lane_id: -1 - disable [isp_image] Isp_FrameRate=30 Isp_Bayer=BAYER_BGGR [vi_dev] Input_mod=VI_MODE_MIPI Work_mod =0..."

New page

== Sensor ==
Camera needs _4l driver, got it from telegram channel. Source?
config as follows:
* /etc/sensors/sc223a_4l_i2c_1080p.ini
<syntaxhighlight lang="bash" line="1">
[sensor]
Sensor_type=stSnsSc223aObj
Mode=WDR_MODE_NONE
DllFile=libsns_sc223a_4l.so

[mode]
input_mode=INPUT_MODE_MIPI
raw_bitness=10

[mipi]
lane_id = 0|1|-1|-1|-1|-1|-1|-1| ;lane_id: -1 - disable

[isp_image]
Isp_FrameRate=30
Isp_Bayer=BAYER_BGGR

[vi_dev]
Input_mod=VI_MODE_MIPI
Work_mod =0 ;VI_WORK_MODE_1Multiplex = 0
;VI_WORK_MODE_2Multiplex,
;VI_WORK_MODE_4Multiplex
Combine_mode =0 ;Y/C composite or separation mode
;VI_COMBINE_COMPOSITE = 0 /*Composite mode */
;VI_COMBINE_SEPARATE, /*Separate mode */
Comp_mode =0 ;Component mode (single-component or dual-component)
;VI_COMP_MODE_SINGLE = 0, /*single component mode */
;VI_COMP_MODE_DOUBLE = 1, /*double component mode */
Clock_edge =1 ;Clock edge mode (sampling on the rising or falling edge)
;VI_CLK_EDGE_SINGLE_UP=0, /*rising edge */
;VI_CLK_EDGE_SINGLE_DOWN, /*falling edge */
Mask_num =2 ;Component mask
Mask_0 =0xFFF00000
Mask_1 =0x0
Scan_mode = 1;VI_SCAN_INTERLACED = 0
;VI_SCAN_PROGRESSIVE,
Data_seq =2 ;data sequence (ONLY for YUV format)
;----2th component U/V sequence in bt1120
; VI_INPUT_DATA_VUVU = 0,
; VI_INPUT_DATA_UVUV,
;----input sequence for yuv
; VI_INPUT_DATA_UYVY = 0,
; VI_INPUT_DATA_VYUY,
; VI_INPUT_DATA_YUYV,
; VI_INPUT_DATA_YVYU

Vsync =1 ; vertical synchronization signal
;VI_VSYNC_FIELD = 0,
;VI_VSYNC_PULSE,
VsyncNeg=1 ;Polarity of the vertical synchronization signal
;VI_VSYNC_NEG_HIGH = 0,
;VI_VSYNC_NEG_LOW /*if VIU_VSYNC_E
Hsync =0 ;Attribute of the horizontal synchronization signal
;VI_HSYNC_VALID_SINGNAL = 0,
;VI_HSYNC_PULSE,
HsyncNeg =0 ;Polarity of the horizontal synchronization signal
;VI_HSYNC_NEG_HIGH = 0,
;VI_HSYNC_NEG_LOW
VsyncValid =1 ;Attribute of the valid vertical synchronization signal
;VI_VSYNC_NORM_PULSE = 0,
;VI_VSYNC_VALID_SINGAL,
VsyncValidNeg =0;Polarity of the valid vertical synchronization signal
;VI_VSYNC_VALID_NEG_HIGH = 0,
;VI_VSYNC_VALID_NEG_LOW
Timingblank_HsyncHfb =0 ;Horizontal front blanking width
Timingblank_HsyncAct =1920 ;Horizontal effetive width
Timingblank_HsyncHbb =0 ;Horizontal back blanking width
Timingblank_VsyncVfb =0 ;Vertical front blanking height
Timingblank_VsyncVact =1080 ;Vertical effetive width
Timingblank_VsyncVbb=0 ;Vertical back blanking height
Timingblank_VsyncVbfb =0 ;Even-field vertical front blanking height(interlace, invalid progressive)
Timingblank_VsyncVbact=0 ;Even-field vertical effetive width(interlace, invalid progressive)
Timingblank_VsyncVbbb =0 ;Even-field vertical back blanking height(interlace, invalid progressive)
InputDataType=1 ;VI_DATA_TYPE_YUV = 0,VI_DATA_TYPE_RGB = 1,
DataRev =FALSE ;Data reverse. FALSE = 0; TRUE = 1
DevRect_x=200
DevRect_y=20
DevRect_w=1920
DevRect_h=1080
</syntaxhighlight>